View A3967SLB_296277.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3967
PRELIMINARY INFORMATION
(Subject to change without notice) June 20, 2002
MICROSTEPPING DRIVER WITH TRANSLATOR
The A3967SLB is a complete microstepping motor driver with built-in translator. It is designed to operate bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capability of 30 V and 750 mA. The A3967SLB includes a fixed off-time current regulator that has the ability to operate in slow, fast, or mixed current-decay modes. This current-decay control scheme results in reduced audible motor noise, increased step accuracy, and reduced power dissipation. The translator is the key to the easy implementation of the A3967SLB. By simply inputting one pulse on the STEP input the motor will take one step (full, half, quarter, or eighth depending on two logic inputs). There are no phase-sequence tables, high-frequency control lines, or complex interfaces to program. The A3967SLB interface is an ideal fit for applications where a complex P is unavailable or over-burdened. Internal circuit protection includes thermal shutdown with hysteresis, under-voltage lockout (UVLO) and crossover-current protection. Special power-up sequencing is not required. The A3967SLB is supplied in a 24-lead SOIC with copper batwing tabs. The tabs are at ground potential and need no insulation.
Data Sheet 26184.24
REF RC2 SLEEP OUT2B LOAD SUPPLY2 GND GND SENSE2 OUT2A STEP DIR MS1
1 2 3 4 5 6 7 8 9 9 10 11 12 VBB2
/8
PWM TIMER
24 23 22 21
PFD RC1 RESET OUT1B LOAD SUPPLY1 GND GND SENSE1 OUT1A ENABLE LOGIC SUPPLY MS2
VBB1 20 19 18 17 16
TRANSLATOR & CONTROL LOGIC VCC
15 14 13
Dwg. PP-075-2
ABSOLUTE MAXIMUM RATINGS at TA = +25C
Load Supply Voltage, VBB ............. 30 V Output Current, IOUT Continuous ..................... 750 mA* Peak ................................ 850 mA Logic Supply Voltage, VCC ........... 7.0 V Logic Input Voltage Range, VIN (tw >30 ns) .... -0.3 V to VCC + 0.3 V (tw <30 ns) .......... -1 V to VCC + 1 V Sense Voltage, VSENSE .............. 0.68 V Reference Voltage, VREF ................. VCC Package Power Dissipation, PD ......................................... 2.2 W Operating Temperature Range, TA ........................... -20C to +85C Junction Temperature, TJ ......... +150C Storage Temperature Range, TS ......................... -55C to +150C
* Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified current rating or a junction temperature of 150C.
FEATURES
s s s s s s s 750 mA, 30 V Output Rating SatlingtonTM Sink Drivers Automatic Current-Decay Mode Detection/Selection 3.0 V to 5.5 V Logic Supply Voltage Range Mixed, Fast, and Slow Current-Decay Modes Internal UVLO and Thermal Shutdown Circuitry Crossover-Current Protection
Always order by complete part number, e.g., A3967SLB .
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
FUNCTIONAL BLOCK DIAGRAM
LOGIC SUPPLY VCC REF. SUPPLY REF
1 14
LOAD SUPPLY UVLO AND FAULT DETECT VBB1
20
/8
DAC + -
SENSE
RC1
23
PWM LATCH BLANKING MIXED DECAY
OUT1A
16
OUT1B
21
3 STEP 10
PWM TIMER
TRANSLATOR
DIR 11 RESET 22 MS1 12 MS2 13
SENSE1
CONTROL LOGIC
17
5
VBB2
SLEEP
3
ENABLE 15 VPF
5
OUT2A PWM TIMER 3
PWM LATCH BLANKING MIXED DECAY
9
PFD
2
OUT2B
4
RC2 + DAC
6 7 18 19
8
SENSE2
Dwg. FP-050-3
Table 1. Microstep Resolution Truth Table MS1 L H L H MS2 L L H H Resolution Full step (2 phase) Half step Quarter step Eighth step
2
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 2002 Allegro MicroSystems, Inc.
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
ELECTRICAL CHARACTERISTICS at TA = +25C, VBB = 30 V, VCC = 3.0 V to 5.5V (unless otherwise noted) Limits Characteristic Output Drivers Load Supply Voltage Range VBB Operating During sleep mode Output Leakage Current ICEX VOUT = VBB VOUT = 0 V Output Saturation Voltage VCE(sat) Source driver, IOUT = -750 mA Source driver, IOUT = -400 mA Sink driver, IOUT = 750 mA Sink driver, IOUT = 400 mA Clamp Diode Forward Voltage VF IF = 750 mA IF = 400 mA Motor Supply Current IBB Outputs enabled RESET high Sleep mode Control Logic Logic Supply Voltage Range Logic Input Voltage VDD VIN(1) VIN(0) Logic Input Current IIN(1) IIN(0) Maximum STEP Frequency Blank Time Fixed Off Time fSTEP tBLANK toff Rt = 56 k, Ct = 680 pF Rt = 56 k, Ct = 680 pF VIN = 0.7VDD VIN = 0.3VDD Operating 3.0 0.7VDD - -20 -20 500* 700 30 5.0 - - <1.0 <1.0 - 950 38 5.5 - 0.3VDD 20 20 - 1200 46 V V V A A kHz ns s 4.75 0 - - - - - - - - - - - - - <1.0 <-1.0 - - - - 1.4 1.1 - - - 30 30 20 -20 2.1 2.0 1.3 0.5 1.6 1.4 5.0 200 20 V V A A V V V V V V mA A A Symbol Test Conditions Min. Typ. Max. Units
continued next page ...
www.allegromicro.com
3
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
ELECTRICAL CHARACTERISTICS at TA = +25C, VCC = 30 V, VDD = 3.0 V to 5.5V (unless otherwise noted) Limits Characteristic Control Logic (cont'd) Mixed Decay Trip Point PFDH PFDL Ref. Input Voltage Range Reference Input Impedance Gain (Gm) Error (note 3) VREF ZREF EG VREF = 2 V, Step = 3 VREF = 2 V, Step = 5 VREF = 2 V, Step = 9 Thermal Shutdown Temp. Thermal Shutdown Hysteresis UVLO Enable Threshold UVLO Hysteresis Logic Supply Current TJ TJ VUVLO VUVLO IDD Outputs enabled Outputs off Sleep mode Increasing VDD Operating - - 1.0 120 - - - - - 2.45 0.05 - - - 0.6VCC 0.21VCC - 160 - - - 165 15 2.7 0.10 65 - - - - VCC 200 10 5.0 5.0 - - 2.95 - 85 9.0 100 V V V k % % % C C V V mA mA A Symbol Test Conditions Min. Typ. Max. Units
* Operation at a step frequency greater than the specified minimum value is possible but not warranteed. 8 microstep/step operation. NOTES: 1. Typical Data is for design information only. 2. Negative current is defined as coming out of (sourcing) the specified device terminal. 3. EG = ([VREF/8] - VSENSE)/(VREF/8)
4
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Functional Description
Device Operation. The A3967 is a complete microstepping motor driver with built in translator for easy operation with minimal control lines. It is designed to operate bipolar stepper motors in full-, half-, quarterand eighth-step modes. The current in each of the two output H-bridges is regulated with fixed off time pulsewidth modulated (PWM) control circuitry. The H-bridge current at each step is set by the value of an external current sense resistor (RS), a reference voltage (VREF), and the DAC's output voltage controlled by the output of the translator. At power up, or reset, the translator sets the DACs and phase current polarity to initial home state (see figures for home-state conditions), and sets the current regulator for both phases to mixed-decay mode. When a step command signal occurs on the STEP input the translator automatically sequences the DACs to the next level (see table 2 for the current level sequence and current polarity). The microstep resolution is set by inputs MS1 and MS2 as shown in table 1. If the new DAC output level is lower than the previous level the decay mode for that H-bridge will be set by the PFD input (fast, slow or mixed decay). If the new DAC level is higher or equal to the previous level then the decay mode for that H-bridge will be slow decay. This automatic current-decay selection will improve microstepping performance by reducing the distortion of the current waveform due to the motor BEMF. Reset Input (RESET). The RESET input (active low) sets the translator to a predefined home state (see figures for home state conditions) and turns off all of the outputs. STEP inputs are ignored until the RESET input goes high. Step Input (STEP). A low-to-high transition on the STEP input sequences the translator and advances the motor one increment. The translator controls the input to the DACs and the direction of current flow in each winding. The size of the increment is determined by the state of inputs MS1 and MS2 (see table 1). Microstep Select (MS1 and MS2). Input terminals MS1 and MS2 select the microstepping format per table 1. Changes to these inputs do not take effect until the STEP command (see figure). Direction Input (DIR). The state of the DIRECTION input will determine the direction of rotation of the motor. Internal PWM Current Control. Each H-bridge is controlled by a fixed off time PWM current-control circuit that limits the load current to a desired value (ITRIP). Initially, a diagonal pair of source and sink outputs are enabled and current flows through the motor winding and RS. When the voltage across the current-sense resistor equals the DAC output voltage, the current-sense comparator resets the PWM latch, which turns off the source driver (slow-decay mode) or the sink and source drivers (fast- or mixed-decay modes). The maximum value of current limiting is set by the selection of RS and the voltage at the VREF input with a transconductance function approximated by: ITRIPmax = VREF/8RS The DAC output reduces the VREF output to the current-sense comparator in precise steps (see table 2 for % ITRIPmax at each step). ITRIP = (% ITRIPmax/100) x ITRIPmax Fixed Off-Time. The internal PWM current-control circuitry uses a one shot to control the time the driver(s) remain(s) off. The one shot off-time, toff, is determined by the selection of an external resistor (RT) and capacitor (CT) connected from the RC timing terminal to ground. The off time, over a range of values of CT = 470 pF to 1500 pF and RT = 12 k to 100 k is approximated by: toff = RTCT
www.allegromicro.com
5
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Functional Description (cont'd)
RC Blanking. In addition to the fixed off time of the PWM control circuit, the CT component sets the comparator blanking time. This function blanks the output of the current-sense comparator when the outputs are switched by the internal current-control circuitry. The comparator output is blanked to prevent false over-current detection due to reverse recovery currents of the clamp diodes, and/ or switching transients related to the capacitance of the load. The blank time tBLANK can be approximated by: tBLANK = 1400CT Enable Input (ENABLE). This active-low input enables all of the outputs. When logic high the outputs are disabled. Inputs to the translator (STEP, DIRECTION, MS1, MS2) are all active independent of the ENABLE input state. Shutdown. In the event of a fault (excessive junction temperature) the outputs of the device are disabled until the fault condition is removed. At power up, and in the event of low VCC, the under-voltage lockout (UVLO) circuit disables the drivers and resets the translator to the home state. Sleep Mode (SLEEP). An active-low control input used to minimize power consumption when not in use. This disables much of the internal circuitry including the outputs. A logic high allows normal operation and startup of the device in the home position. Percent Fast Decay Input (PFD). When a STEP input signal commands a lower output current from the previous step, it switches the output current decay to either slow-, fast-, or mixed-decay depending on the voltage level at the PFD input. If the voltage at the PFD input is greater than 0.6VDD then slow-decay mode is selected. If the voltage on the PFD input is less than 0.21VDD then fast-decay mode is selected. Mixed decay is between these two levels. Mixed Decay Operation. If the voltage on the PFD input is between 0.6VDD and 0.21VDD, the bridge will operate in mixed-decay mode depending on the step sequence (see figures). As the trip point is reached, the device will go into fast-decay mode until the voltage on the RC terminal decays to the voltage applied to the PFD terminal. The time that the device operates in fast decay is approximated by: tFD = RTCTIn (0.6VDD/VPFD) After this fast decay portion, tFD, the device will switch to slow-decay mode for the remainder of the fixed off-time period.
6
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Timing Requirements
(TA = +25C, VCC = 5 V, Logic Levels are VCC and Ground)
STEP
50%
C A B
D
MS1/MS2/ DIR/RESET
E
SLEEP
Dwg. WP-042
A. Minimum Command Active Time Before Step Pulse (Data Set-Up Time) ..... 200 ns B. Minimum Command Active Time After Step Pulse (Data Hold Time) ............ 200 ns C. Minimum STEP Pulse Width ...................... 1.0 s D. Minimum STEP Low Time ......................... 1.0 s E. Maximum Wake-Up Time ......................... 1.0 ms
www.allegromicro.com
7
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Applications Information
Layout. The printed wiring board should use a heavy ground plane. For optimum electrical and thermal performance, the driver should be soldered directly onto the board. The load supply terminal, VBB, should be decoupled with an electrolytic capacitor (>47 F is recommended) placed as close to the device as possible. To avoid problems due to capacitive coupling of the high dv/dt switching transients, route the bridge-output traces away from the sensitive logic-input traces. Always drive the logic inputs with a low source impedance to increase noise immunity. Grounding. A star ground system located close to the driver is recommended. The 24-lead SOIC has the analog ground and the power ground internally bonded to the power tabs of the package (leads 6, 7, 18, and 19). Current Sensing. To minimize inaccuracies caused by ground-trace IR drops in sensing the output current level, the current-sense resistor (RS) should have an independent ground return to the star ground of the device. This path should be as short as possible. For low-value sense resistors the IR drops in the printed wiring board sense resistor's traces can be significant and should be taken into account. The use of sockets should be avoided as they can introduce variation in RS due to their contact resistance. Allegro MicroSystems recommends a value of RS given by RS = 0.5/ITRIPmax Thermal protection. Circuitry turns off all drivers when the junction temperature reaches 165C, typically. It is intended only to protect the device from failures due to excessive junction temperatures and should not imply that output short circuits are permitted. Thermal shutdown has a hysteresis of approximately 15C.
ALLOWABLE PACKAGE POWER DISSIPATION in WATTS
2.5
RJT = 6C/W
2.0
RJA is measured on typical twosided PCB with minimal copper ground area (77C/W) or with 3.57 in2 copper ground area (49C/W). See also, Application Note 29501.5, Improving Batwing Power Dissipation.
1.5
R JA = 49C/W
1.0
0.5
R JA = 77C/W
0 25 50 75 100 125 150
Dwg. GP-019C
TEMPERATURE in C
8
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Table 2. Step Sequencing (DIR = L) Phase 2 Current [%Itripmax] 0.00 19.51 38.27 55.56 70.71 83.15 92.39 98.08 100.00 98.08 92.39 83.15 70.71 55.56 38.27 19.51 0.00 -19.51 -38.27 -55.56 -70.71 -83.15 -92.39 -98.08 -100.00 -98.08 -92.39 -83.15 -70.71 -55.56 -38.27 -19.51 0.00 Phase 1 Current [%Itripmax] 100.00 98.08 92.39 83.15 70.71 55.56 38.27 19.51 0.00 -19.51 -38.27 -55.56 -70.71 -83.15 -92.39 -98.08 -100.00 -98.08 -92.39 -83.15 -70.71 -55.56 -38.27 -19.51 0.00 19.51 38.27 55.56 70.71 83.15 92.39 98.08 100.00
Full Step #
Half Step # 1
Quarter Step # 1 2
Eighth Step # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Step Angle 0 11.25 22.50 33.75 45* 56.25 67.50 78.75 90 101.25 112.50 123.75 135 146.25 157.50 168.75 180 191.25 202.50 213.75 225 236.25 247.50 258.75 270 281.25 292.50 303.75 315 326.25 337.50 348.75 360
1
2
3 4
3
5 6
2
4
7 8
5
9 10
3
6
11 12
7
13 14
4
8
15 16
9 * Home state.
17
www.allegromicro.com
9
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Full Step Operation MS1 = MS2 = L, DIR = H
STEP INPUT
SLOW DECAY
70.7%
PHASE 1 CURRENT
-70.7%
SLOW DECAY
70.7%
PHASE 2 CURRENT
-70.7%
Dwg. WK-004-19
The vector addition of the output currents at any step is 100%.
10
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Half Step Operation MS1 = H, MS2 = L, DIR = H
STEP INPUT
MIXED DECAY SLOW DECAY SLOW DECAY SLOW DECAY MIXED DECAY MIXED DECAY SLOW DECAY MIXED DECAY MIXED DECAY SLOW DECAY
100% 70.7%
PHASE 1 CURRENT
-70.7% -100%
SLOW DECAY MIXED DECAY MIXED DECAY SLOW DECAY MIXED DECAY SLOW DECAY
100% 70.7%
PHASE 2 CURRENT
70.7% -100%
Dwg. WK-004-18
The mixed-decay mode is controlled by the percent fast decay voltage (VPFD). If the voltage at the PFD input is greater than 0.6VDD then slow-decay mode is selected. If the voltage on the PFD input is less than 0.21VDD then fast-decay mode is selected. Mixed decay is between these two levels.
www.allegromicro.com
11
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Quarter Step Operation MS1 = L, MS2 = H, DIR = H
STEP INPUT
SLOW DECAY
MIXED DECAY
SLOW DECAY
MIXED DECAY
100% 70.7% 38.3%
PHASE 1 CURRENT
-38.3% -70.7% -100%
MIXED DECAY
SLOW DECAY
MIXED DECAY
SLOW DECAY
100% 70.7% 38.3%
PHASE 2 CURRENT
-38.3% -70.7% -100%
Dwg. WK-004-17
The mixed-decay mode is controlled by the percent fast decay voltage (VPFD). If the voltage at the PFD input is greater than 0.6VDD then slow-decay mode is selected. If the voltage on the PFD input is less than 0.21VDD then fast-decay mode is selected. Mixed decay is between these two levels.
12
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
8 Microstep/Step Operation MS1 = MS2 = H, DIR = H
STEP INPUT
SLOW DECAY
MIXED DECAY
SLOW DECAY
MIXED DECAY
100% 70.7% 38.3%
PHASE 1 CURRENT
-38.3% -70.7% -100%
MIXED DECAY
SLOW DECAY
MIXED DECAY
SLOW DECAY
100% 70.7% 38.3%
PHASE 2 CURRENT
-38.3% -70.7% -100%
Dwg. WK-004-16
The mixed-decay mode is controlled by the percent fast decay voltage (VPFD). If the voltage at the PFD input is greater than 0.6VDD then slow-decay mode is selected. If the voltage on the PFD input is less than 0.21VDD then fast-decay mode is selected. Mixed decay is between these two levels.
www.allegromicro.com
13
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
Terminal List Terminal Name REF RC2 SLEEP OUT2B LOAD SUPPLY2 GND SENSE2 OUT2A STEP DIR MS1 MS2 LOGIC SUPPLY ENABLE OUT1A SENSE1 GND LOAD SUPPLY1 OUT1B RESET RC1 PFD Terminal Number 1 2 3 4 5 6, 7 8 9 10 11 12 13 14 15 16 17 18, 19 20 21 22 23 5
Terminal Description Gm reference input Analog input for fixed offtime - bridge 2 Logic input H bridge 2 output B VBB2, the load supply for bridge 2 Analog and power ground Sense resistor for bridge 2 H bridge 2 output A Logic input Logic Input Logic input Logic input VCC, the logic supply voltage Logic input H bridge 1 output A Sense resistor for bridge 1 Analog and power ground VBB1, the load supply for bridge 1 H bridge 1 output B Logic input Analog Input for fixed offtime - bridge 1 Mixed decay setting
The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use.
14
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
24
13
0.0125 0.0091
0.2992 0.2914
0.419 0.394 0.050 0.016
0.020 0.013
1
2
3
0.6141 0.5985
0.050
BSC NOTE 1 NOTE 3
0 TO 8
Dimensions in Inches (for reference only)
.0926 .1043 0.0040 MIN.
Dwg. MA-008-25A in
24
13
0.32 0.23
7.60 7.40
10.65 10.00 1.27 0.40
0.51 0.33
1
2
3
15.60 15.20
1.27
BSC NOTE 1 NOTE 3
0 TO 8
Dimensions in Millimeters (controlling dimensions)
.65 .35 0.10 MIN.
NOTES: 1. 2. 3. 4.
Dwg. MA-008-25A mm
Exact body and lead configuration at vendor's option within limits shown. Lead spacing tolerance is non-cumulative. Webbed lead frame. Leads 6, 7, 18, and 19 are internally one piece. Supplied in standard sticks/tubes of 31 devices or add "TR" to part number for tape and reel.
www.allegromicro.com
15
3967 MICROSTEPPING DRIVER WITH TRANSLATOR
MOTOR DRIVERS
Output Ratings* Part Number INTEGRATED CIRCUITS FOR BRUSHLESS DC MOTORS 3-Phase Power MOSFET Controller -- 28 V 3933 3-Phase Power MOSFET Controller -- 50 V 3932 3-Phase Back-EMF Controller/Driver 900 mA 14 V 8902-A INTEGRATED BRIDGE DRIVERS FOR DC AND BIPOLAR STEPPER MOTORS Dual Full Bridge with Protection & Diagnostics 500 mA 30 V 3976 PWM Current-Controlled Dual Full Bridge 650 mA 30 V 3966 PWM Current-Controlled Dual Full Bridge 650 mA 30 V 3968 Microstepping Translator/Dual Full Bridge 750 mA 30 V 3967 PWM Current-Controlled Dual Full Bridge 750 mA 45 V 2916 PWM Current-Controlled Dual Full Bridge 750 mA 45 V 2919 PWM Current-Controlled Dual Full Bridge 750 mA 45 V 6219 PWM Current-Controlled Dual Full Bridge 800 mA 33 V 3964 PWM Current-Controlled Dual DMOS Full Bridge 1.0 A 35 V 3973 PWM Current-Controlled Full Bridge 1.3 A 50 V 3953 PWM Current-Controlled Dual Full Bridge 1.5 A 45 V 2917 PWM Current-Controlled DMOS Full Bridge 1.5 A 50 V 3948 PWM Current-Controlled Microstepping Full Bridge 1.5 A 50 V 3955 PWM Current-Controlled Microstepping Full Bridge 1.5 A 50 V 3957 PWM Current-Controlled Dual DMOS Full Bridge 1.5 A 50 V 3972 PWM Current-Controlled Dual DMOS Full Bridge 1.5 A 50 V 3974 PWM Current-Controlled Full Bridge 2.0 A 50 V 3952 PWM Current-Controlled DMOS Full Bridge 2.0 A 50 V 3958 Microstepping Translator/Dual DMOS Full Bridge 2.5 A 35 V 3977 Dual DMOS Full Bridge 2.5 A 50 V 3971 PWM Current-Controlled DMOS Full Bridge 3.0 A 50 V 3959 UNIPOLAR STEPPER MOTOR & OTHER DRIVERS Unipolar Stepper-Motor Quad Drivers 1.0 A 46 V 7024 & 7029 Unipolar Microstepper-Motor Quad Driver 1.2 A 46 V 7042 Unipolar Stepper-Motor Translator/Driver 1.25 A 50 V 5804 Unipolar Stepper-Motor Quad Driver 1.8 A 50 V 2540 Unipolar Stepper-Motor Quad Driver 3.0 A 46 V 7026 Unipolar Microstepper-Motor Quad Driver 3.0 A 46 V 7044 * Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits or over-current protection voltage limits. Negative current is defined as coming out of (sourcing) the output. Complete part number includes additional characters to indicate operating temperature range and package style. Also, see 3175, 3177, 3235, and 3275 Hall-effect sensors for use with brushless dc motors. Function
16
115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000

▲Up To Search▲

Price & Availability of A3967SLB

	To Download A3967SLB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .